Home › Vehicles › Infiniti › Infiniti QX60 Wheel Bearing Part Numbers
The short version
- The front QX60 wheel bearing is 513296 for 2014-2015 and again for 2017-2018. The catalogs skip 2016 entirely.
- The rear splits by drivetrain from 2014 through 2016: AWD uses 512548, FWD uses 512388.
- From 2017 on the rear listing simplifies to 512548.
- The QX60 shares its platform, and its front hub number, with the Nissan Pathfinder R52.
Infiniti built the QX60 on a Nissan crossover platform, and the parts catalogs make that lineage obvious. One model year in particular has a gap that is easy to miss.
The QX60’s front and rear numbers
The front hub assembly is 513296, listed for 2014 and 2015 with a 32-tooth spline count, then again for 2017 and 2018 on the 3.5L engine. The rear depends on drivetrain for 2014 through 2016, then simplifies for 2017 and 2018.
Nothing in the catalogs fills the front listing for 2016. That is the one year worth double-checking before ordering.
QX60 wheel bearing part numbers
| Years | Detail | Number |
|---|---|---|
| 2017-2018 | Rear hub | 512548 check price |
| 2017-2018 | Front hub assembly, 3.5L | 513296 check price |
| 2014-2016 | Rear hub, AWD | 512548 check price |
| 2014-2016 | Rear hub, FWD | 512388 check price |
| 2014-2015 | Front hub assembly, 32-tooth spline | 513296 check price |
Every model year this chart resolves: 2014, 2015, 2016, 2017 and 2018.
Price links lead to Amazon searches for that number. As an Amazon Associate this site earns from qualifying purchases.
Lookups run through the cross reference page.
The front hub assembly, 513296, is listed for 2014 and 2015 with a 32-tooth spline count. It shows up again for 2017 and 2018 on the 3.5L engine, but the catalogs carry no 2016 row.
Confirm the spline count against the old part or the VIN before ordering for a 2016 QX60. A mismatched spline count will not seat correctly even if the base number looks right.
Same platform as the Pathfinder
The QX60 rides on the same platform as the Nissan Pathfinder R52, and the front hub number, 513296, belongs to that shared family rather than to Infiniti alone. That is normal for Infiniti’s broader lineup, which leans heavily on Nissan platforms.
Rear numbers still depend on drivetrain. Do not assume a Pathfinder rear part fits a QX60 without checking AWD or FWD status first.
A three row crossover’s wear pattern
The QX60 is a three row crossover. Fully loaded trips add real weight over the rear axle that the bearings have to carry, and that shows up when a rear bearing fails earlier than expected.
Compared to a smaller crossover like the Nissan Murano, the QX60’s extra length and seating capacity add more weight the rear bearings see daily.
Diagnosing a QX60 wheel bearing
- Listen for a speed-linked hum. The sound builds with road speed and does not change with engine RPM.
- Note which drivetrain the car has. Since the rear number splits by AWD versus FWD, confirm that before pulling a part number.
- Jack up the affected corner. Rock the wheel at 12 and 6 o’clock with it off the ground to check for play.
- Spin the wheel by hand. Grinding or roughness while spinning free with the brake released points at a failing bearing.
- Match the old part on a 2016 model. The front number is not clearly listed for that year, so confirm the spline count against the removed part or the VIN.
Common questions
What is the QX60 wheel bearing part number up front?
It is 513296 for 2014 and 2015, and again for 2017 and 2018 on the 3.5L engine. The 2016 model year is not clearly listed, so match the old part or the VIN.
Does the QX60 wheel bearing differ between AWD and FWD?
At the rear, yes. AWD cars use 512548 and FWD cars use 512388 for 2014 through 2016, while 2017-2018 rear cars use 512548.
Does the QX60 share wheel bearings with the Pathfinder?
The QX60 and the Pathfinder R52 share a platform, and the front hub assembly comes from the same family of parts. Confirm the exact number through the cross reference first.
Why is there no clear number for a 2016 QX60?
The catalogs simply skip that model year in the front hub listing. Match the old part or the VIN rather than guessing between the 2015 and 2017 numbers.
Is the QX60 wheel bearing a bolt-on hub assembly?
Yes, front and rear are complete hub assemblies, not a serviceable cone and cup setup. That is standard for a modern crossover in this class.