Home › Vehicles › Jeep › Jeep Wrangler › 2007-2018 Jeep Wrangler JK Wheel Bearing Part Numbers
The short version
- The 2007-2018 Jeep JK wheel bearing catalogs document only the first few years. Front: 513272 (Moog, 2007-2010) with Timken’s HA590242 as a 2007-2008 parallel. Rear: SET10 and 9912S through 2008.
- The JK ran twelve model years, but the catalogs stop naming numbers well before the run ends.
- For 2011-2018 fronts and 2009-2018 rears, match the old part or the VIN. Use the documented rows as reference points, not guarantees.
- The rear axle stayed Dana 44 with a flanged shaft the whole generation. There is no axle split to sort out, unlike the earlier Wranglers.
The Jeep JK ran from 2007 to 2018, the longest single production span of any Wrangler generation. This page covers Jeep JK wheel bearing numbers for that run, front and rear. It includes an honest note about where the catalogs run out.
Jeep JK wheel bearing numbers at a glance
The front hub is 513272 from Moog, with Timken’s HA590242 as a parallel listing for 2007-2008.
The rear is Dana 44 with a flanged shaft, using SET10 and seal 9912S, documented only through 2008.
Jeep Wrangler JK wheel bearing part numbers
| Years | Detail | Number |
|---|---|---|
| 2007-2010 | Front hub, Moog | 513272 check price |
| 2007-2008 | Front hub, Timken parallel listing | HA590242 check price |
| 2007-2008 | Rear, Dana 44 flanged shaft, bearing | SET10 check price |
| 2007-2008 | Rear, Dana 44 flanged shaft, seal | 9912S check price |
Price links lead to Amazon searches for that number. As an Amazon Associate this site earns from qualifying purchases.
Lookups run through the cross reference page.
This page covers the 2007-2018 Jeep Wrangler JK: 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018. Other years live on the main Wrangler wheel bearing page.
A Jeep JK wheel bearing search for anything past 2010 up front will not find a documented row. The same is true past 2008 at the rear.
The axle architecture did not change through 2018, and the aftermarket sells hubs for every year of the run.
Match the part against the old one or the VIN. Do not trust a listing that claims a fit the catalogs never documented.
Year by year
2007 and 2008 carry both catalog rows. That means the Moog front hub 513272 alongside Timken’s HA590242, and the rear SET10 with seal 9912S.
2009 and 2010 keep the Moog front hub, 513272. The rear and the Timken front parallel drop out of the documented catalogs by then.
2011 through 2018 run the same JK architecture the whole way, but nothing here is separately documented. Match the old part or the VIN, with 513272 and SET10 as the closest documented reference.
The JK between the TJ and what came after
The JK replaced the TJ in 2007 and kept the same idea of a solid axle at both ends. The parts themselves are not shared between generations. The prior generation is covered on the 1997-2006 TJ page.
How a solid axle changes wear and duty compared to independent suspension is on the drive type page.
Diagnosing a Jeep JK wheel bearing
- Pull the old part number off the hub before ordering anything for a 2011 or later JK.
- Rock each wheel at twelve and six with it off the ground.
- Listen for a hum that grows with road speed rather than with steering angle.
- Check preload and end play on the front hub as part of the diagnosis.
- Compare a listing’s claimed fitment against the old part before trusting it for later years.
General checking steps are on the checking page, and end play basics are on the preload page.
Common questions
What wheel bearing does a Jeep JK use?
The front is 513272 from Moog, with Timken’s HA590242 documented as a 2007-2008 parallel. The rear is SET10 with seal 9912S, documented through 2008.
What wheel bearing does a 2012 Jeep JK use?
2012 sits past where the catalogs stop naming numbers, so match the old part or the VIN. 513272 up front and SET10 at the rear remain the documented reference points.
Why do only the early JK years have listed numbers?
The catalogs used for this page stop documenting new rows after 2008 to 2010. The JK kept building through 2018 regardless.
Does the JK rear axle ever change from Dana 44?
Not in the catalogs. The flanged shaft Dana 44 rear runs the whole generation. That is unlike the axle split on the earlier YJ and TJ.
Is the JK front hub a bolt on part?
Yes, it bolts to the knuckle as a complete assembly rather than pressing in.