Home › Vehicles › Toyota › Toyota T100 Wheel Bearing Part Numbers › 1993-1998 Toyota T100 Wheel Bearing Part Numbers
The short version
- A 1996 Toyota T100 front wheel bearing replacement means serviceable cones, cups and seals. It is never a hub assembly, on 2WD or 4WD trucks.
- The 2WD front uses inner cone and cup M38549H-M38510, outer cone and cup 1380H-1328X, and seal 1948, across all six model years.
- The 4WD front carries its own seals, cones, cups and outer set through 1997. The catalogs stop documenting a 1998 4WD front listing after that.
- The rear axle on every T100 is solid, with no wheel bearing number of its own.
Toyota built the T100 from 1993 to 1998 with fully serviceable front wheel bearings on both 2WD and 4WD trucks. A 1996 Toyota T100 front wheel bearing replacement calls for individual cones, cups and seals, not a bolt on hub. The two drivetrains use different parts throughout.
T100 wheel bearing numbers, 1993 to 1998
A 1996 Toyota T100 front wheel bearing replacement on a 2WD truck needs seal 1948, inner cone and cup M38549H-M38510, and outer cone and cup 1380H-1328X.
A 4WD truck through 1997 needs its own seal, cone and cup set. The catalogs stop short of a documented 1998 4WD listing.
Toyota T100 wheel bearing part numbers
| Years | Detail | Number |
|---|---|---|
| 1998 | Front 4WD | not documented, match old part or VIN |
| 1993 to 1997 | Front 4WD, outer bearing set | SET47 check price |
| 1993 to 1997 | Front 4WD, outer seal | 710266 check price |
| 1993 to 1997 | Front 4WD, inner cone and cup | JLM104948-JLM104910 check price |
| 1993 to 1997 | Front 4WD, seal | 710092 check price |
| 1993 to 1998 | Front 2WD, outer cone and cup | 1380H-1328X check price |
| 1993 to 1998 | Front 2WD, inner cone and cup | M38549H-M38510 check price |
| 1993 to 1998 | Front 2WD, seal | 1948 check price |
| 1993 to 1998 | Rear, solid axle | not documented, match old part or VIN |
Price links lead to Amazon searches for that number. As an Amazon Associate this site earns from qualifying purchases.
Lookups run through the cross reference page.
Every 2WD year and every 4WD year through 1997 has a full serviceable listing. The catalogs we hold stop short for a 1998 4WD front.
Match the number the old part carries or run the VIN. Do not borrow the 1997 listing on faith.
This page covers the 1993-1998 Toyota T100: 1993, 1994, 1995, 1996, 1997, 1998. Other years live on the main T100 wheel bearing page.
Year by year
1993 through 1998 share the same 2WD front listings without any change. A 1996 Toyota T100 front wheel bearing replacement on a 2WD truck looks identical to one done in 1993 or 1998.
The 4WD front listings run 1993 through 1997 unchanged. They stop being documented for 1998, the one gap in the whole range.
Serviceable bearings, not a hub
Nothing on the T100 front end is a sealed hub assembly. That means repacking rather than pressing in a new hub is the normal service here. The rear is a solid axle, covered separately at axle bearing versus wheel bearing.
Setting preload correctly matters more on a serviceable bearing than on a sealed hub. There is no factory preset to fall back on.
Diagnosing a Toyota T100 wheel bearing
- Check for grease at the hub cap. A leaking seal on a serviceable bearing often shows up as grease on the wheel or backing plate.
- Feel for play with the wheel off the ground. Grab the tire top and bottom and rock it; see how to check a wheel bearing.
- Confirm drivetrain before ordering parts. A 2WD and 4WD T100 never share a front cone, cup or seal.
- Listen for a change in a turn. A loose or dry bearing often gets louder or quieter depending on the turn; see wheel bearing noise in a turn.
- Recheck preload after service. A bearing set too tight or too loose will fail again quickly, regardless of part quality.
Common questions
What wheel bearing parts does a 1996 Toyota T100 need up front?
A 1996 Toyota T100 front wheel bearing replacement on a 2WD truck needs seal 1948, inner cone and cup M38549H-M38510, and outer cone and cup 1380H-1328X. A 4WD truck needs seal 710092, inner cone and cup JLM104948-JLM104910, outer seal 710266, and outer set SET47.
Does the 1998 T100 4WD front use the same parts as 1997?
The catalogs do not carry a documented 1998 4WD front listing. Match the number the old part carries or run the VIN, rather than assuming the 1997 parts carry over.
Is the T100 front a hub assembly?
No. Every front listing on the T100 is a serviceable cone, cup or seal, never a hub assembly.
What bearing does the T100 rear axle use?
The rear is a solid axle with no documented wheel bearing number of its own. Match the old part or run the VIN.
Do 2WD and 4WD T100 trucks share any front part?
No. The two drivetrains use separate seals, cones and cups throughout the entire 1993 to 1998 run.