Home › Vehicles › Honda › Honda City Wheel Bearing Part Numbers
The short version
- A Honda City wheel bearing search in US parts catalogs turns up empty. Honda never sold the City in the United States.
- Owners have to order through Honda’s parts channel in a market where the City is actually sold, matched by VIN.
- Some online listings borrow numbers from the Honda Fit or the Civic. That substitution is never verified for the City.
- Whether a City generation uses a press-in or bolt-on hub assembly varies by generation and market. No single design claim covers every City.
Honda has sold the City as a subcompact sedan across Asia and Latin America for more than three decades. It has never once appeared in a US showroom.
What the Honda City wheel bearing catalogs actually show
Moog, Timken, and National build their Honda charts around models Honda actually sold in the United States. The City was never one of them.
That leaves owners with no domestic reference number to fall back on at all.
Honda City wheel bearing part numbers
| Years | Detail | Number |
|---|---|---|
| 2020 to present (fifth generation, GN) | Sold across Asia and Latin America, not in the US | match by VIN or old part |
| 2014 to 2020 (fourth generation, GM6) | Sold across Asia, not in the US | match by VIN or old part |
| 1981 to 2014 (earlier generations) | Sold in Asia from launch, not in the US | match by VIN or old part |
No model year on this chart resolves to a catalog number. On this chart a 2020 or newer Honda City sits past the catalogs, and a 1981 through 2019 Honda City is not documented, so those cars go by the old part or the VIN.
Lookups run through the cross reference page.
Some listings sell a Honda City wheel bearing using a part number lifted from the Honda Fit or the Civic. Those two Hondas do have documented US charts.
That is a guess dressed up as a fit, not a confirmed match. Verify against the old part before buying.
The Civic and Accord comparison
The Civic is the closest Honda in size and market positioning to the City. The two were never built on the exact same platform in every generation, though.
The larger Accord is even further removed. It is useful mainly as a sanity check on Honda’s general hub design, not a parts match.
Press-in and bolt-on differences
Whether a City generation uses a press-in bearing or a bolt-on hub assembly changes by generation and by market. No single answer covers the whole model line.
That is exactly why VIN matching matters more here than with a Honda sold in one consistent US spec. Honda’s full US lineup shows how many of its global small cars never crossed over.
Diagnosing a Honda City wheel bearing
- Listen for a speed related hum. A worn bearing growls or hums louder as road speed increases, independent of engine RPM.
- Turn the wheel to isolate the noise. Weaving gently side to side on an empty road can make the sound louder or quieter on the affected side.
- Jack the corner and check for play. Rock the tire at the 12 and 6 o’clock positions with the wheel off the ground.
- Spin the wheel by hand. Roughness, grinding, or clicking usually points to a pitted bearing race.
- Check for ABS warning lights. A damaged wheel speed sensor tone ring can trip a fault code before the noise becomes obvious.
Common questions
Can a Honda Fit wheel bearing fit a City?
Not automatically. The two share some Honda engineering, but no catalog confirms a direct match. Treat any Fit based listing as unverified until checked against the old part.
Why is there no Honda City wheel bearing in US parts stores?
Because Honda never sold the City in the United States. US catalogs only cover models that actually reached American dealers.
Does every City generation use the same hub design?
No. Press-in and bolt-on designs both appear across the City’s history depending on generation and market. The design has to be confirmed for the specific car.
Is the Civic a reliable stand-in for City parts?
It is the closest reference in size and market segment, but not a confirmed parts match. Use it as a starting point, then verify by VIN or old part.
How should someone order a Honda City wheel bearing?
Through a Honda parts channel in a country where the City is sold, using the VIN. A specialist able to match the physical old part is another route.